Water geyser is the most common home appliance in India and requires the same level of maintenance as any other home appliance. While various geysers like havells standard geyser, kenstar water geyser, etc manufacturers provide the best parts capable of withstanding constant heating and cooling, it’s important to keep in mind that even the best parts will deteriorate if subjected to continuous pressure.
Listed below are the top 10 tips to consider when performing maintenance or installing a water geyser:
Space around the geyser
When installing a water heater, keep some space between the apparatus and the surrounding walls. Without enough wiggle room to inspect the water heater’s components, the technician will be unable to service or repair it properly. While some people place the geyser directly on top of the toilet to improve access, it makes it more difficult for the technician to reach the appliances. It is far preferable to locate it on a portion of the wall with nothing beneath the geyser and away from damp areas such as the shower, bathtub, or toilet.
Put the water heater at a sufficient height:
According to experts, you should install the geyser at a minimum height of 1.8 meters or 6 feet from the floor. This ensures that the water pressure is sufficient and that you receive a strong stream of hot water rather than a trickle from your faucet.
Connectors and switches
Some of the best-selling geysers these days come with Miniature Circuit Breaker, capable of shutting down the electricity in the event of a power surge. This will help to eliminate the possibility of a water heater short circuit. Additionally, keep the switch a sufficient distance away from small children but not so high that you or any adult has difficulty reaching it.
Save more electricity by lowering the temperature
Water heater maintenance is critical because it results in energy savings! If you set the temperature to a lower value, the water will reach that temperature more quickly. Reduced temperature requires the geyser to work less, extending its life.
It is especially critical for families with small children to lower the thermostat. Thus, maintaining your water heater is critical to ensuring that you never run out of hot water during the winter. It is advisable to consider an energy-saving geyser, such as the 5-Star Havells standard geyser.
Avoid leaving the geyser on for extended periods
Most people prefer to leave the geyser on for extended periods, particularly in the morning. The general belief is that because everyone requires warm water before leaving for work or school, leaving the geyser saves time.
Because leaving the geyser on for extended periods will shorten its life, it makes more sense to turn it on 5 minutes before you need it rather than half an hour before. Maintaining your water heater regularly can help extend its life. You can purchase a Havells geyser online which can be operated from your mobile app.
Check the anode rod inside the tank before winter
Large geysers are equipped with an anti-corrosion rod. By attracting rust and impurities from the water, this rod will prevent the tank from corroding or rusting. However, as a result of this, it corrupts away after a few years.
Experts recommend inspecting the anode rod every three years to determine if the outer layer of magnesium has eroded and exposed at least 6 inches of the inner steel core.
Conduct a visual inspection of the pressure release valve
At least once a year, verify that the temperature and pressure release valves are functioning properly. This can be verified by repeatedly releasing the pressure. If the relief valve on the water heater is leaking, this is a serious problem. Drain some water from your water geyser and disconnect the discharge tube.
Keep an eye on the plug
Due to power fluctuations and the use of low-capacity wiring for the power socket, your switch will occasionally spark. Additionally, you will notice burn marks on the pins of your plug as the increased electricity wattage heats the plug and the pins, leaving burn traces.
To avoid future electrical short circuits caused by this, it is always preferable to use brand new plugs and sockets that have been properly wired and plugged in.
Plastic inlet and outlet pipes should be replaced with metal pipes
It is always preferable to use metal inlet and outlet pipes over the standard plastic ones with a geyser. Additionally, keep an eye on the joints regularly. If you notice whitish deposits from hard water or rust around the joints, the inlet or outlet pipe should be replaced.
Sufficient space
Ascertain that sufficient space is available for the geyser unit. The area or space must correspond to the size of the electric geyser. For example, always consider the geyser’s size when installing it in the bathroom or kitchen, you can consider a water heater at easy EMI which comes with a standard size suitable for all types of space. Adequate space enables the geyser unit to be cleaned and serviced properly.